|LB49-14/5||Keck Clip, Yellow, 14/23 Joint Size, Pack of 5||$3.75|
|LB49-19/5||Keck Clip, Blue, 19/26 Joint Size,Pack of 5||$4.25|
|LB49-24/5||Keck Clip, Green, 24/29 joint size,Pack of 5||$4.75|
|LB49-29/5||Keck Clip, Red, 29/32 Joint Size,Pack of 5||$5.20|
| Alcohol Hydrometer Set|
Alcohol Hydrometers use specific gravity to measure percent alcohol by volume in your distilled product. Each hydrometer is carefully calibrated and individually retested for accuracy. This set includes our specially made hydrometer cylinder.
NEW! Now including Temperature Correction Chart
| Brix Hydrometer Set|
Brix Hydrometers are calibrated to show the percentage of sucrose by weight. The Brix Scale is based on the following: 1° Brix = 1% sucrose by weight at specified temperature (20°C). The Brix scale is commonly used to measure the sugar content of various juices and "ripeness" of fruit. This set includes a cylinder.
| Hydrometer Cylinder|
This Hydrometer Cylinder has been made specifically to fit our alcohol and brix hydrometers. The inside diameter is just 1.125 in., so you can use a much smaller sample than with an ordinary 250ml cylinder. With extra-heavy 3 point base to stay flat on your bench. This cylinder also has a nice pour spout. For quick and easy reading there are no graduations. Made of borosilicate glass.
| Dial Thermometer, 0 to 220 Fahrenheit|
The same thermometer used in our Master Distiller kit: accurate and easy-to-read dial has a 1.5 inch diameter face and 8 inch stem length. Comes with a spring clamp for quick mounting on pots of flasks. Temperature range is 0 to 220 Fahrenheit. Made of stainless steel.
| Distillation Accessories Kit|
Everything you need to connect your water-cooled condenser to a standard faucet:
| Graham Condenser Kit|
For simple distillation, water-cooled Graham type condenser, consists of an inner coil running through a cooling chamber. Included are faucet adapter, hose barb and tubing to connect to a standard faucet. The vapor inlet is fitted with a length of high-temperature Norprene® tubing for connection to your boiling flask. 13" Overall Length, body diameter is 1 1/4".
14/25 joint size, flask to condenser
| Ceramic Top Hot Plate|
Designed for laboratory use, this is a variable heat control, ceramic top heater. The heat is generated from resistant coils recessed into the ceramic top. It also comes with a removable ceramic top plate especially designed for round bottom flasks. Features:
Please note: This heater is designed for quick and rapid heating. The variable temperature adjustment is limited. If you need finely adjustable temperature settings we recommend our digital magnetic stirrers.
|AP05-TOP||Ceramic Top Hot Plate Replacement Top||$6.13|
For adapting a standard faucet or garden hose to fit 3/8" tubing used to supply cooling water to the condenser for distillation.
Dual Thread Faucet Adaptor is used to covert ordinary faucets to standard Garden Hose Thread.
Garden Hose to 3/8" Tubing Adaptor is used to reduce the garden hose to 3/8 tubing.
Both adaptors are needed to run your condenser from an ordinary faucet. If you are using a garden hose for your water source, you only need the Garden Hose Adaptor.
|LB150||Garden Hose to 3/8" Tubing adaptor||$3.40|
|LB149||Dual Thread Faucet Adaptor||$6.30|
High grade, medium wall tubing, for school and laboratory use. This tubing is made of seamless red rubber and sold by the 10' roll.
28ml = 1 fluid ounce
25mm = 1 inch
Metric Conversion Calculator
|LB111-01||Rubber Tubing, 3/16"||3/16"||10'||$6.45|
|LB111-02||Rubber Tubing, 1/4"||1/4"||10'||$6.45|
|LB111-03||Rubber Tubing, 5/16"||5/16"||10'||$6.45|
|LB111-04||Rubber Tubing, 3/8"||3/8"||10'||$6.45|